Misc/General Technical

4,190 topics in this forum

1. Fitting Compomotives with different offsets

   By Donie- C, April 4, 2019
   • 7 replies
   • 1,300 views
   • 
   • jackherer
   • April 6, 2019

2. Nut + Bolt Rebuild, 205 Gti...where To Source Nuts + Bolts?

   By c_robinson, July 1, 2012   

   • obsesseivecompulsive?!
   • 15 replies
   • 3,067 views
   • 
   • MrAndy
   • March 27, 2019

3. Ready to restore my car after 11 years

   By Bally, March 18, 2019
   • 2 replies
   • 1,513 views
   • 
   • cybernck
   • March 26, 2019

4. Bottom engine mount

   By xstian, March 6, 2019
   • 7 replies
   • 1,569 views
   • 
   • welshpug
   • March 15, 2019

5. Tacho

   By woodymi16, March 9, 2019
   • 3 replies
   • 1,093 views
   • 
   • woodymi16
   • March 11, 2019

6. Fuel clip and line routing

   By Telf, March 10, 2019
   • 6 replies
   • 1,147 views
   • 
   • stumpyjag
   • March 11, 2019

7. Fuel breather filter?

   By Telf, March 6, 2019
   • 2 replies
   • 857 views
   • 
   • Telf
   • March 6, 2019

8. CLUTCH CABLE REPLACEMENT

   • 1
   • 2

   By 4ll5op, March 3, 2019
   • 42 replies
   • 7,399 views
   • 
   • 4ll5op
   • March 6, 2019

9. Sunroof sealant

   By Telf, March 6, 2019
   • 0 replies
   • 798 views
   • 
   • Telf
   • March 6, 2019

10. No Reverse Light

    • 1
    • 2

    By Luke, April 11, 2014   

    • Reverse
    • light
    • (and 1 more)

      Tagged with:

      • Reverse
      • light
      • reversing
    • 36 replies
    • 10,338 views
    • 
    • Callum
    • March 5, 2019

11. Help wanted with regards to bonnet cable

    By wellsyuk, March 2, 2019
    • 0 replies
    • 839 views
    • 
    • wellsyuk
    • March 2, 2019

12. 205 xs wiring

    By K20205, February 22, 2019
    • 5 replies
    • 1,627 views
    • 
    • K20205
    • February 23, 2019

13. Locking Wheel Nut Help

    By East_Hud, February 18, 2019
    • 8 replies
    • 1,572 views
    • 
    • Tom Fenton
    • February 22, 2019

14. Rollcage advice

    By jamie_1992, November 18, 2018
    • 22 replies
    • 5,217 views
    • 
    • camgti
    • February 12, 2019

15. Where to source nylon lever bearing - fits in gear selection bar

    By Jakob, January 23, 2019
    • 8 replies
    • 2,530 views
    • 
    • SRDT
    • February 9, 2019

16. Terminal extractor kits

    By Cobalt_drill_bit, October 12, 2018
    • 6 replies
    • 1,751 views
    • 
    • Gavin Waddell
    • January 30, 2019

17. This hose that runs from Induction Hose to somewhere?

    By johnyma22, January 17, 2019
    • 3 replies
    • 1,164 views
    • 
    • MrAndy
    • January 28, 2019

18. Gearbox Mount

    By Simmo, August 2, 2016
    • 23 replies
    • 5,065 views
    • 
    • jackherer
    • January 24, 2019

19. Connector part number

    By Telf, January 23, 2019
    • 3 replies
    • 1,049 views
    • 
    • jackherer
    • January 23, 2019

20. Fuel Line Retaining Clips - Sourcing question.

    By johnyma22, January 12, 2019
    • 4 replies
    • 1,279 views
    • 
    • johnyma22
    • January 16, 2019

21. Object in Fuel Tank

    By rob_mitch, January 7, 2019
    • 0 replies
    • 1,117 views
    • 
    • rob_mitch
    • January 7, 2019

22. Jacking up the rear using the axle?

    By Philpooma, December 30, 2018
    • 2 replies
    • 1,133 views
    • 
    • Philpooma
    • December 30, 2018

23. Blower working on full speed only - Where is the blower resistor?

    By farkash7, December 23, 2018
    • 0 replies
    • 944 views
    • 
    • farkash7
    • December 23, 2018

24. TIG rods for inlets manifolds?

    By Richie-Van-GTi, December 8, 2018
    • 1 reply
    • 1,111 views
    • 
    • petert
    • December 8, 2018

25. Standard air horn location / fitment help

    By IanH, November 18, 2018
    • 5 replies
    • 2,308 views
    • 
    • welshpug
    • November 28, 2018