Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Search the Community

Showing results for tags 'Cable'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Categories

  • Technical Articles & Guides
    • 205 GTI Basics & Buying Guides
    • Engine Maintenance & Upgrades
    • Gearbox & Drivetrain
    • Brakes, Suspension & Steering
    • Body, Interior and ICE
    • Misc & General Technical
  • Our Partners
  • Car Photo of the Month

Forums

  • Links
    • 205 GTI Drivers Main Website
  • Support and News
    • Website & Forum Updates and News
  • Technical
    • XU 8v Engine Maintenance and Performance Upgrades
    • XU 16v Engine Maintenance and Performance Upgrades
    • XU Engine & Gearbox Service and Maintenance - ARCHIVE
    • XU Engine & Gearbox Modifications and Performance Upgrades - ARCHIVE
    • TU Engine Maintenance and Performance Upgrades
    • Non-XU/TU Engine Maintenance and Performance Upgrades
    • Aftermarket Engine Management Systems
    • Gearbox & Drivetrain
    • Brakes, Suspension & Steering
    • Body, Interior & ICE
    • Misc/General Technical
    • Other Model-specific Technical Questions
    • Technical Archive
    • 405Mi16.com Technical Forums Archive
  • General
    • General Car Chat
    • Drivers' Cars Discussion Topics
  • Car Projects & Works
    • Large Scale & Special Projects
    • Car Restorations, Overhauls & Upgrades
    • Trackday & Race/Rally Prep
    • Engine Work
    • Body, Misc & Non-Car Work
    • Projects & Works Starters
  • For Sale, Wanted and Group Buys
    • PugsForSale.co.uk Classifieds

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Found 2 results

  1. sport1901966

    New Mi16 Harness Build

    I've just got round to writing up my build of a new Mi16 loom for the 205 conversion and thought I'd post it up here as hopefully it'll be of interest to you guys. Be warned - it's a bit of a longun! When I bought the Mi16 engine ready for the conversion it came with the BX16v harness that had been partially modified already. Unfortunately, it was a bit of a mess but after a bit of time spent with a multimeter I had got my head around it. I made some repairs and judged it was ok to use, at least temporarily. Having fitted the harness I then discovered the ECU would not run the fuel pump as it should. The software logic in the ECU is designed so that the fuel pump will run for about 1 second as soon as the key is turned to the ignition position, then, when the key is turned to the starter position and the engine turns over, the ECU will detect a signal from the Crank Angle Sensor (CAS) and activate the fuel pump to start supplying fuel (it continues to do this all the time it is receiving a signal from the CAS, i.e. when the engine is turning) . From a wiring point of view the ECU controls the fuel pump activation by earthing the Fuel Pump Relay. However in its current state the original harness didn’t do this, and even having spent ages checking it over I couldn’t work out why, I even got to the point where I suspected the ECU of being at fault. To get by I wired the Fuel Pump into a toggle switch on the dash. The other obvious flaw to this harness was the length due to the ECU being mounted under the driver seat in the BX16v. Because of the condition of the harness and the poor layout in the 205, I had always intended to build a new harness specifically designed for the conversion in both layout and fundamental wiring design. This time came around sooner than planned as I had a few teething problems during the early days of running the car. First was the melting of a whole chunk of the harness when the bonnet scissor prop cut into the loom and earthed the main live cable: The repair ended up like this: Following this the fan blades on the alternator cut through the Crank Angle Sensor shielded cable, obviously completely stopping the engine from running. Which prompted the fabrication of this: Obviously the original condition and the subsequent repairs to these issues left the harness open to all kinds of reliability issues so I got started with designing the new harness.
  2. Hi, Car - 1988 Gearbox - BE1 lift up reverse I have replaced my clutch cable today. It was a 3 hour job and a good experience. I have now adjusted the cable properly too. However, I got a new problem now. Every time I try and select first, it goes into reverse. What seems to have happened is that the reverse lock is not working. I have done a search on the forums and according to one of the old posts it seems to be a reverse cable issue (that may have been stuck open) I dont really know what to do next, or how to locate this cable to look at further. What do I do next? Can somebody please help. Thanks
×