j4mes205 0 Posted March 26, 2012 Hi guys got a 306 gti 6 donor car on its ways was just wanting to know does gti 6 engine and box bolt straight in and do I need anything else cheers james Share this post Link to post Share on other sites
Daviewonder 533 3 Cars Posted March 26, 2012 It bolts straight in but you need to modify the exhaust manifold for clearance. Share this post Link to post Share on other sites
Daviewonder 533 3 Cars Posted March 26, 2012 You'll probably have issues with the master cylinder hitting the rocker cover too. You need to tilt the servo backwards and trim the timing belt cover as far as I know. Share this post Link to post Share on other sites
j4mes205 0 Posted March 26, 2012 What driveshafts would i need Share this post Link to post Share on other sites
allye 530 3 Cars Posted March 26, 2012 GTI shafts, depending on what hubs you'll be using, also depends if you use the 6 speed, if so you'll need to change the diff for a 205 BE3 item but maintain the GTI6 crownwheel. Share this post Link to post Share on other sites
sambaileyw 2 Posted March 26, 2012 GTI shafts, depending on what hubs you'll be using, also depends if you use the 6 speed, if so you'll need to change the diff for a 205 BE3 item but maintain the GTI6 crownwheel. Out of interest could you swap hubs to 306 items, and then run 306 driveshafts? Share this post Link to post Share on other sites
Anthony 1,003 Posted March 26, 2012 It's not a hub issue, but the length of the splines on the inner CV differing between early (205) and late (306/Xsara) diffs There is plenty of info on GTi-6 engine conversion if you do a search, showing what you need, what issues you're liable to come across, and most other common questions. Share this post Link to post Share on other sites
Miles 331 1 Cars Posted March 26, 2012 You should find loads of pics in the projects section as well, Just make sure the belts done Share this post Link to post Share on other sites
welshpug 1,737 Posted March 26, 2012 (edited) and the water pump Edited March 26, 2012 by welshpug Share this post Link to post Share on other sites
Baz 421 Posted March 27, 2012 And tensioner/idler... Share this post Link to post Share on other sites
Spiky 37 Posted March 27, 2012 dont forget to unlock the ECU, ingnition/or car runing, and unplug the ECU if you no good with electrics, and loom can be found here http://forum.205gtidrivers.com/index.php?showtopic=137329 306 hubs give positve camber, so jsut stick with 1.9 hubs and drive shafts tilt engine a little to fit, or modify the bulkhead (i done this way), or you can modify the exmanifold tilt the servo on the pedal box, gives more clearance for the master cylinder Share this post Link to post Share on other sites
chipstick 382 1 Cars Posted March 27, 2012 I wrote a fairly detailed list of things needed in my project thread (link in sig). Have a nosey and if you have any specific questions for anything you are unsure of, drop me a message and i'l help Share this post Link to post Share on other sites
j4mes205 0 Posted March 27, 2012 Thanks for replies guys it seems to be quite long. Winded to get it done sovmight have to sort parts and get a plan of action together Just atm im having issues with driveshaft seals on a standard 205 1.9 ive replaced 2 seals gently on drivers side but still seems to leak am i right in thinking could not be driveshaft seal but it could be coming out of speedo cable input Thanks for the help as a total newbie to 205s as came from subarus lol Share this post Link to post Share on other sites
Spiky 37 Posted March 27, 2012 could be either really best to get under there, clean all the oil off and see where it's leaking from a test (if your brave) put on axle stands put in second gear start the car up and let it run on tick over to get the wheels going, get underneath and see if you can see it leaking Share this post Link to post Share on other sites
Anthony 1,003 Posted March 27, 2012 Remember that the driveshaft seals need to sit a little proud - if you put them in flush, they'll usually leak. Share this post Link to post Share on other sites
j4mes205 0 Posted March 27, 2012 Aha that could be my problem i have put them in flush its so frustrating that it isnt sealing i will have to fit a new one not flush and also have a look at the speedo cable the passenger side i replaced is fine thats the frustrating thing Share this post Link to post Share on other sites
Miles 331 1 Cars Posted March 27, 2012 use OE Pug ones, Never had a problem with those, Share this post Link to post Share on other sites