Guest puggti Posted May 31, 2003 ok, now my engine mountings seem to be shagged, i have changed the top one which i belive is the easiest What other ones are there and are they hard to change?!?! I will have the gearbox out soon so is there on to replace here too?!? Share this post Link to post Share on other sites
C_W 3 1 Cars Posted May 31, 2003 The one on the gearbox (under the batter) is easy to change. When you take the battery off there will be two 13mm nuts and a larger 18mm nut holding the pin from the gaerbox up in the mount. Share this post Link to post Share on other sites
Guest himbigchief Posted June 1, 2003 One more on the bottom rear of the engine. Bolts the engine to the subframe iirc. James Share this post Link to post Share on other sites
sleeper205 0 Posted June 1, 2003 just to let peeps know, 205 TU and XU bottom mounts seem to be the same. i can't see anything physically different about them. Share this post Link to post Share on other sites
Guest puggti Posted June 1, 2003 Ok u see this bottom one is it a bugger to change?!? Share this post Link to post Share on other sites
Guest doughboy Posted June 1, 2003 Not if you take the whole casing to a garage with a press Share this post Link to post Share on other sites
Guest puggti Posted June 1, 2003 can i buy the bottom one?? if so where shall i get these mounts from Am i right in thinkin that the 405 uses the same mounts?!? If so where can i get them from>?? Thanks for all ur help Share this post Link to post Share on other sites
Guest timH Posted June 1, 2003 the bottom one is a bitch to change, unless you take it to a garage with a press, like said above. Did mine with a BFH, and still didn't get it entirely in the right place. The 2 top ones are dead easy. good luck. Share this post Link to post Share on other sites
Guest puggti Posted June 1, 2003 can i not buy the bottom one complete?!? If so where shall i get my mountings from?? GSF? Share this post Link to post Share on other sites
205man 0 Posted June 1, 2003 euro car parts charge £4.25+vat for just the lower mount itself or £44.50+vat complete, would be cheaper to just but the mount and pay about a tenner for someone to press it in. peugeot charge about £90 for the complete thing alan Share this post Link to post Share on other sites
Guest puggti Posted June 2, 2003 But is the bottom one EASY to change apart from the pressing? Share this post Link to post Share on other sites
Guest puggti Posted June 3, 2003 ok i went to GSF and bought some engine mounts, i asked for every1 they have for the 205 gti, i got given a circle thing with rubber in side and another circle thing with something sticking out with thread in it!! They confused me!! Any1 got any photos of what the mounts should look like, ie the one under the battery tray and the one on the subframe so i can see if i have the right ones!! Also i need to get the one near the cam belt end, i can see what this looks like so i dont need fotos of this!! Pug Share this post Link to post Share on other sites
Guest doughboy Posted June 3, 2003 mounts top left with gold bit on top is gearbox mount. below that is the lower mount. the 3 bits on the right make up the upper mount. Share this post Link to post Share on other sites
Guest puggti Posted June 3, 2003 Thanks mate, i have the top right one and the bottom left one (the bottom letf one i have looks a little bit diff with the same metal casing and the rubber inside, it doesnt have the silver bit on it but has a hole so it will do!! The one on the top right is that easy to fit, is that the one under the battery tray? Not bad for a tenner :-) Share this post Link to post Share on other sites
Guest doughboy Posted June 3, 2003 is that the one under the battery tray? nope, that's the top left one. they will look slightly different cos that pic is of the group n ones. Share this post Link to post Share on other sites
Guest puggti Posted June 3, 2003 So the top right one goes where then? Share this post Link to post Share on other sites
Guest doughboy Posted June 3, 2003 look 4 posts up m8. Share this post Link to post Share on other sites
Guest puggti Posted June 3, 2003 ok yeah thanks Any1 else want to help me?? Share this post Link to post Share on other sites