Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Dendle89

L417 RAC - 3rd time lucky

Recommended Posts

Dendle89
17 hours ago, welshpug said:

not too far then, a mate  (Goliath) has a workshop off Winterstoke Road  near Ashton Gate, I'm sure we can sort it for you once you have it rolling.

 

 

presumably its likely to have had a rebuild in the past?

Unknown and nothing that proves it has. I think I’ve found the source of the air leak on between inlet and head - so I’ve ordered a therma tech gasket. Anyone know what bolts I need to replace the existing inlet manifold bolts - believe they are the standard ones.

Share this post


Link to post
Share on other sites
welshpug

you'll need slightly longer bolts I'd imagine, not by much though, i've come across a few that have pulled threads with a thicker gasket used.

 

 

  • Like 1

Share this post


Link to post
Share on other sites
welshpug

originals are M8x30 socket head capscrews

  • Like 1

Share this post


Link to post
Share on other sites
Dendle89
Posted (edited)

Small amount of progress;

 

- Wired up the rad fans which is connected to the loom via the standard connector

- Swapped out the clear indicators to orange ones

- new smaller intercooler (little thicker but fits under the valance better

- New braided hydraulic lines for the charger oil 

 

55400027825_f4bc2079e2_b.jpg

 

 

So close to getting this ready now! hopefully be done in the next few weeks!!

Edited by Dendle89
  • Like 2

Share this post


Link to post
Share on other sites
Dendle89
Posted (edited)

Share this post


Link to post
Share on other sites
Dendle89

Back to the drawing board.. it ran really well, but the intake temp was a little on the high side.

 

I wanted to move the airfilter over to the right and found Spoox charge £400 for that pleasure

 

image.png.5cdc26a6df3df4d8267f60b3c45d9c38.png

 

 

Instead I purchased some alloy tube and airfilter from K&N with a slight bend away from the block so give it the best possible chance.

 

55503850031_192f4605f8_b.jpg

 

Decided that I'm also going to push the rad back to original mounting place and re-route the charger to intercooler pipework. I have a short oil filter (FRAM - PH5796) on order to help me with that so I can route the pipe that way.

Edited by Dendle89

Share this post


Link to post
Share on other sites
Spesh

how are those quick release's working out on the bumper?

Share this post


Link to post
Share on other sites
chris 417 mi
On 8/10/2026 at 10:24 AM, Dendle89 said:

Just put some new gaz coilovers on mine aswell :) 

be good to see this in the flesh again if you take it to pugfest next year ? Ill hopefully have her sister finished by then 

Share this post


Link to post
Share on other sites
petert

Yeah, it's definitely tough getting enough intercooler in a 205 to keep the inlet temps down. This is my friend's Parry. An E85 blend helps.

Parry Supercharger Engine Bay.jpg

  • Like 1

Share this post


Link to post
Share on other sites
welshpug

if its like any other Lynx setup the iat is still in the throttle body, as a suck through system,    so if the inlet temps there are high then I dread to think what they actually are at the valve.

Share this post


Link to post
Share on other sites
Dendle89
On 9/2/2026 at 10:09 PM, Spesh said:

how are those quick release's working out on the bumper?

Brilliant - would recommend. Bumper removal and install under a 30 seconds is a game changer.

 

On 9/3/2026 at 8:30 AM, chris 417 mi said:

Just put some new gaz coilovers on mine aswell :) 

be good to see this in the flesh again if you take it to pugfest next year ? Ill hopefully have her sister finished by then 

Yes! went this year but didn't have the car ready. But my aim is to have this on the road before May next year!

 

19 hours ago, welshpug said:

if its like any other Lynx setup the iat is still in the throttle body, as a suck through system,    so if the inlet temps there are high then I dread to think what they actually are at the valve.

I think its one of the flaws of the boost set up for sure, but moving the filter away from the engine has brought back down to normal temp ranges.

  • Like 1

Share this post


Link to post
Share on other sites
petert
On 9/4/2026 at 6:44 PM, Dendle89 said:

Brilliant - would recommend. Bumper removal and install under a 30 seconds is a game changer.

 

How are you managing the side mounting points?

Share this post


Link to post
Share on other sites
Dendle89
On 9/7/2026 at 12:28 AM, petert said:

How are you managing the side mounting points?

Two bolts either side on the "wing" which are nipped up with nuts and the pins on the front of the bars - 30 seconds max on/off!

 

 

Change of direction.. I purchased the short radiator for Retro, Race and Rally - didn't want to as they're pricy but £600 later I'm chuffed as it all fits in neatly behind the bumper now.

 

55541648635_2a90f425db_b.jpg

 

Few more little adjustments and this will be ready to go again!

Edited by Dendle89
  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×