Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Sign in to follow this  
Takentoxs

Head Work

Recommended Posts

Takentoxs

Can anyone recommend a good place to get my tu3s breathed on. Ports, valve seats, balance and skim, usual stuff I guess unless I am missing something. An idea of cost would be helpful too.

Share this post


Link to post
Share on other sites
johnnyboy666

Sandy on here is pretty much the TU guru, he can probably point you in the right direction.

Share this post


Link to post
Share on other sites
juice willis

Sorry to highjack thread.. Looking into putting twin webers on my xs. Would it be worth putting a vtr 8v head on? Would there be any power gains? Mainly thinking of doing this for the wider availability of mods especially inlet manifold. Cheers

Share this post


Link to post
Share on other sites
Sandy

Thanks for the nod, but I'm really stacked out at the moment and not really taking on headwork I'm afraid, however my pal Mark Shillaber might well be able to help. SRD Ltd, 01566778779.

Share this post


Link to post
Share on other sites
And

Sorry to highjack thread.. Looking into putting twin webers on my xs. Would it be worth putting a vtr 8v head on? Would there be any power gains? Mainly thinking of doing this for the wider availability of mods especially inlet manifold. Cheers

Only if you can up the compression back up so you would require Pistons, as not even a heavily skimmed head is enuf.

Edited by And

Share this post


Link to post
Share on other sites
juice willis

perhaps I should just put a 16 valve in and be done :) tough decision as it's such a good engine. Finding any bits I would like for reasonable money for the tu3s is a pita though.

Share this post


Link to post
Share on other sites
welshpug

the prices of parts for either engine when you start building proper competition types arent too different at all save for where you have double the camshafts and valves.

 

differences come when you set goals that are easier achieved with much milder tuning of a larger capacity engine tgat has more valvesm

Share this post


Link to post
Share on other sites
juice willis

Good to know! The main thing is finding a reasonably priced weber manifold. About to ask in the wanted section!

Share this post


Link to post
Share on other sites
juice willis

Managed to find 2 separate manifolds designed for the euro rallye, any idea if these would fit?

Share this post


Link to post
Share on other sites
Wallby

I don't think they will fit but I'm not 100%, the bolt pattern is different on the euro rallye head.

Share this post


Link to post
Share on other sites
juice willis

Feared that was the case. There's someone on eBay selling tu3 weber manifolds for 300. Not sure how good they are but cheaper than getting a custom one I suppose. Still, pretty hefty pricetag.

Share this post


Link to post
Share on other sites
NEMCA

You can buy the flange plate profiles for both carb side and manifold side from DAN ST engineering. You can get them in ally or mild steel and have someone make you a manifold.

Share this post


Link to post
Share on other sites
juice willis

Thanks for that NEMCA, definitely considering going down this route, cheers.

Share this post


Link to post
Share on other sites
And

I would look at making as with a small angle up bank you can clear the engine mounting don't cut the mount down to 2 bolts as it will fail.. I remade my mount as well as the made the mainfold, never had a failure since apart from mk1 mount bent form a bad down shift mk2 no issues as was bulked up a bit more.

Share this post


Link to post
Share on other sites
calvinhorse

Tu3 and 1.3 Rallye inlet manifolds are different I'm afraid, the 1.3 is the same as a 1.1 head iirc

Share this post


Link to post
Share on other sites
RossD

I'll be putting my TU engine up for sale soon, its got an SRD cylinder head, 645 catcam, custom RH mount, an inlet manifold made by Colin Satchell (And was used on Sandys own 205 Rallye) and I may also put the Throttle bodies in with the package too, depending on appetite. It's a 1.6, however it bolts straight in. Let me know if it interests you.... Check out my project thread for pictures.

Share this post


Link to post
Share on other sites
juice willis

If the op isn't interested I definitely am.

Share this post


Link to post
Share on other sites
juice willis

Am generally up for giving things a go but not sure about fabricating a manifold, perhaps with a bit of guidance. Have access to welding equipment though. Didn't know it was possible to clear the mount that's good to know.

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
Sign in to follow this  

×