Clarion Pu-9469A Speaker Wiring

[mrfirepro 127 1 Cars]

Been searching for a few hours now but come up blank.

 

Have finally got around to refurbishing and installing the clarion in my build, however the plug has been cut off, I have an ISO to Pug converter so have cut the ISO end off and will solder the Pug male connector directly into the clarion wiring.

 

However the clarion has 6 speaker wires as follows

 

Grey/red stripe

White/red stripe

White

White/Green stripe

Grey/Green stripe

Grey

 

Have assumed there must be a common - or + to the front and rears or is it to the left and rights.....

 

Have popped all speakers to make sure of the phasing (from the ISO connector)

 

Anyone offer any suggestions..

 

I did find a photo posted on here but it seemed to show a common connected to a - and +....

 

 

 

 

[mrfirepro 127 1 Cars]

I didn't think the above post was very clear.

 

If someone has or can take a picture of the plug on the back of the unit it would be most helpful so I can just wire my unit the same.

 

the other cables are

 

black

yellow

blue

red

Blue/white stripe

 

thanks

Edited January 5, 2015 by mrfirepro

[will1991 11 1 Cars]

Mine's not in the car at the moment so hopefully these will have you covered. I've got a few more photos so just shout if you need more.

 

Will

 

 

 

 

 

 

[mrfirepro 127 1 Cars]

Thanks Will,

 

There a big help.

 

Only other cable I have from the Clarion is a yellow which I think is illumination and not used...

[welshpug 1,678]

I'm sure its used on mine, it dims the display at night IIRC.

[will1991 11 1 Cars]

No problem. Where did you find the cable with a male Peugeot end on it? I may need one for something else.

[lightflow 59 1 Cars]

Paul, I have just done all this myself - putting in a brand new 9469A. I have all the wiring info at home. I can post later this evening for you.

 

Ash.

[lightflow 59 1 Cars]

Paul -

this worked for me on my PU-9469A. Only wrinkle for me was on the Blue and White/Blue. On my first PU-9469A they were joined together in a choc block by a previous owner of the stereo and both were connected to the Switched 12v on the loom (29B). When I replicated this when with my brand new PU9469A I found it didnn't respond correctly and I think I ended up just leaving one (it may have been the white/blue) cable open - not connected to anything on the car loom. I found when i tried both that the radio seemed to not switch off into standby properly. Odd, but I got it to work correctly.

Good luck!

White/red stripe LF+

White/Green stripe LF-

Brown/Red (looped to Grey/Red) RF+

Grey RF-

Brown/Red (looped to White/Red) LR+

White LR-

Grey/red RR+

Grey/Green RR-

black - Earth

yellow - (I didn't have a yellow wire)

blue - Switched 12V to 29B on Loom

red - Constant 12V Battery 10C on Loom

Blue/white stripe - I left this open I think, or it could have been the blue - I think it is intended to feed an electric aerial (if you struggle with this join together with Blue from Switched 12V) see discussion at the top.

[mrfirepro 127 1 Cars]

Ashley/Will - Thats great info, thanks.

 

Will - I bought a simple PUG to ISO adapter http://www.ebay.co.uk/itm/PEUGEOT-106-1991-TO-1996-CD-STEREO-ISO-WIRING-LOOM-HARNESS-LEAD-PLUG-PC2-06-4-/360803581571?pt=UK_In_Car_Technology&hash=item540191be83 and cut the ISO end of so it could plug straight into the OE loom.

 

However I have discovered that my connections on the loom are all a little loose and some minor corrosion so I have ordered replacement parts for Pug. On another thread WelshPug posted the part numbers (Thanks WP) for the loom connector which are (assuming I've interpreted them right )

 

6542 65 ELEC CLIP-HOLDR13 VOIES RED 20 (x1)

6542 66 HARNESS CLIPA=3 B=0,35 A 1MM2

 

 

6542 67 HARNESS CLIPA=3 B=1 A 3MM2

 

They will be with me tomorrow so will know if I got it right

Edited January 7, 2015 by mrfirepro

[lightflow 59 1 Cars]

Yup those are the parts. You are doing exactly what I did, reinstating the original loom on the car.

[will1991 11 1 Cars]

Ok thanks. I'm actually after the plug attached to the car end of the loom, rather than to the stereo. Did you order one of those? If so a confirmation of part number would be great! Struggling to find anything on Servicebox.

[mrfirepro 127 1 Cars]

Will,

 

As Ashley has confirmed they are the parts you will need, if you're not replacing the connectors just order the first item. I was expecting them today but as yet still nothing