daneldridge23 15 Posted December 1, 2011 hi guys At presnt i have had my crank lightend balenced and knife edged conrods polished lightend and balenced pistons lightend and ballenced lightened and ballenced flywhell omex throttle boddies with 600 ecu piper fast road cams + pullys now i am considering getting a big valve head but would like your guys opinion first on if another 800 quid is worth the bhp gain from this or not, also what power do you guys think i may produce when im up and running, i kno its only gusses but id still like a few figures Dan Share this post Link to post Share on other sites
Daviewonder 533 3 Cars Posted December 1, 2011 What engine is it? Share this post Link to post Share on other sites
Anthony 1,003 Posted December 1, 2011 There should be the potential for something in the region of 200hp there, but as always, the devil is in the finer details and the setup. The general consensus is that a big valve head is not needed on an Mi, and indeed on the smaller 83mm bore of a 1.9, potentially problemsome due to valve shrouding. There's a big pinned topic about it that you probably want to have a read of, but generally speaking, my opinion is to leave the head alone beyond a refurb and properly recutting the seats with the correct angles. The Mi head flows plenty as it is. To give you some idea, if you have a read of Dr Sarty's build thread, you'll see that his standard Mi head made something in the region of 240-250hp with just a mild inlet cam (although admittedly on a 2.2 litre bottom end). Share this post Link to post Share on other sites
brumster 135 1 Cars Posted December 1, 2011 Ooo, estimates, fun! Ok, I'll punt forward the following, assuming those road cams are fairly mild :- Before the head work : 178bhp After the head work : 180bhp Thankyou, I am available for kids parties also.... Share this post Link to post Share on other sites
daneldridge23 15 Posted December 1, 2011 well if i was going to get the valve job done any ideas on the best people to go to? id love to get close to 200 on a n/a car Share this post Link to post Share on other sites
welshpug 1,737 Posted December 1, 2011 leave the valves alone, higher comp pistons decent cams and longer inlet and better exhaust manifold Share this post Link to post Share on other sites
Miles 331 1 Cars Posted December 1, 2011 Cam spec, If regrinds then around 185, as the other work has no bearing at all or if better cams then the BHP depends on those, Who did the work? Share this post Link to post Share on other sites
camgti 56 Posted December 2, 2011 As said above, don't bother with the BVH. Spend the money chasing compression and cams to make it all work well... The longer inlet will also work wonders Cam Share this post Link to post Share on other sites
brumster 135 1 Cars Posted December 2, 2011 Although it was never dyno'd, I suspect I got somewhere between 190 and 210 depending on whether you wanted pub figures or real-world my arse dyno never complained, and it was relatively competitive in it's class for me to not worry too much about what the figure was. Hey, it drove and pulled nicely, that's the main thing. I won't bore you with the details; if you're interested :- http://forum.205gtidrivers.com/index.php?showtopic=81038 Share this post Link to post Share on other sites
petert 641 Posted December 2, 2011 (edited) Definitely go chasing compression and squish height before big valves. Have a search for that thinner Cometic gasket. A can't recall the post but there's an excellent write up on the value of compression increase alone. edit: found it http://forum.205gtidrivers.com/index.php?showtopic=128397 Edited December 2, 2011 by petert Share this post Link to post Share on other sites
daneldridge23 15 Posted December 2, 2011 That settles it i think 800 quid can be spent better else where, i heard somewhere about pitting a second spring seat washer in to compensate for my 3angle valve work is this true? Dan Share this post Link to post Share on other sites
welshpug 1,737 Posted December 2, 2011 only if the valve spring heights are incorrect. Share this post Link to post Share on other sites
daneldridge23 15 Posted December 2, 2011 I have re cut seats aswell so they would be would they not? Share this post Link to post Share on other sites
welshpug 1,737 Posted December 2, 2011 can't tell without checking them. Share this post Link to post Share on other sites
petert 641 Posted December 2, 2011 If you cut the seats a second shim can only be good, not bad as it will also help the sagged old springs. Share this post Link to post Share on other sites