erbs 42 1 Cars Posted November 22, 2011 Ok i have undone the big bolts on the battery tray and the 2 bolts that hold the AFM,is this now supposed to come off? i am trying to get to the engine mount for replacement Share this post Link to post Share on other sites
allye 530 3 Cars Posted November 22, 2011 There are 2 bolt that through the chassis leg horizontally as well. Share this post Link to post Share on other sites
NeilGTi85 5 Posted November 22, 2011 It quite tight to get to the bolts with the box still in place, try lowering the box slightly for better access Share this post Link to post Share on other sites
erbs 42 1 Cars Posted November 22, 2011 (edited) the 2 bolts,one that faces the rad and one opposite, am i supposed to undone the bolts on the mount itself? will it all come out with battery tray attached? Edited November 22, 2011 by erbs Share this post Link to post Share on other sites
welshpug 1,737 Posted November 22, 2011 if you just want to replace the transmission mounting then its just the 2 13mm nuts either side and the centre 16mm nut, no need to touch the 13mm bolts into the chassis leg. Share this post Link to post Share on other sites
erbs 42 1 Cars Posted November 22, 2011 i also want the tray off to re-paint Share this post Link to post Share on other sites
allye 530 3 Cars Posted November 22, 2011 Just to confirm, there are 4 bolts holding the tray onto the chassis rail and 2 holding the mount onto the tray. I assume the engine is out of the car or gearbox detatched? Share this post Link to post Share on other sites
Baz 421 Posted November 22, 2011 ...and the centre 16mm nut... Which is most commonly an 18mm. Share this post Link to post Share on other sites
erbs 42 1 Cars Posted November 22, 2011 no,just want to replace the engine mount and re-paint tray, i thought this could be done without taking the engine out? Share this post Link to post Share on other sites
Baz 421 Posted November 22, 2011 It's possible but i'd support the engine on a jack or stand, it will all hang off the top and lower mount alone otherwise, there's not alot else on that side holding it all up!! Share this post Link to post Share on other sites
erbs 42 1 Cars Posted November 22, 2011 i have the gearbox supported so just to clarify it cane be done? Share this post Link to post Share on other sites
allye 530 3 Cars Posted November 22, 2011 i have the gearbox supported so just to clarify it cane be done? Yer thats fine, if you have all 4 bolts removed it might just need a good wack! Share this post Link to post Share on other sites
BlueBolt 156 Posted November 22, 2011 Sorry to hijack the thread, but if this is the case thn how do I go about removing the battery to the boot without loosing the battery tray?? Or do I just cut it down or what?? Share this post Link to post Share on other sites
Miles 331 1 Cars Posted November 22, 2011 You might need to remove the N/S Drive shaft to get enough clearance Share this post Link to post Share on other sites
cheesegrater 43 1 Cars Posted November 22, 2011 Sorry to hijack the thread, but if this is the case thn how do I go about removing the battery to the boot without loosing the battery tray?? Or do I just cut it down or what?? Battery tray is used in the loosest of terms it's simply a gearbox mount with a limit at one end and a bolt and wedge affair at the other to hold the battery. I wouldn't be cutting anything. Share this post Link to post Share on other sites
welshpug 1,737 Posted November 22, 2011 you can cut quite a significant amount from it if you relocate the battery. Share this post Link to post Share on other sites