craig_007 1 Posted October 24, 2011 I've been offered a DTA E48 at what I feel is a good price !! What like is this ECU, Is it old hat now or is it still seen as a good unit ? Share this post Link to post Share on other sites
dcc 855 Posted October 24, 2011 its just as capable as the dta s40, just slightly different drivers. if its working, in good order then I think they're still worth £300 ish. Share this post Link to post Share on other sites
craig_007 1 Posted October 24, 2011 The guy is asking £400 with a loom, Doe's that sound fair ? Share this post Link to post Share on other sites
dcc 855 Posted October 24, 2011 very fair. normally looms are in the region of £300 on their own maybe a cheeky £350 offer would be worth it. important to consider who is going to be your mapper before you buy anything though. Sandy is going to be mapping mine for me (e48) Share this post Link to post Share on other sites
craig_007 1 Posted October 24, 2011 Very true, I'm up in Scotland so might struggle with a decent mapper. Share this post Link to post Share on other sites
Anthony 1,003 Posted October 24, 2011 Depends on the loom - is it ready to plug straight into a 205, or at least easily adaptable and built to a high standard? Most looms that I see are what I'd politely call "fit for the bin" they're of such a low standard, built by people that don't know a crimping tool from a wildebeest or a soldering iron from a lampshade That's at the top end of the price range for an DTA E48 these days in my opinion, so would really need to have a very good loom for that, and worth checking the which revision the ECU is (it's hand written on the front) as some of the older variants don't support some of the features (and given the age of an E48 it is lacking the features of many modern ECU's anyway). From memory, V34 is the later one and many features aren't supported below V30. Share this post Link to post Share on other sites
craig_007 1 Posted October 24, 2011 The loom was in a escort running a C20XE so it'll require work to fit my car I should imagine. Thanks for the insight all the same, I might just give this a miss. Share this post Link to post Share on other sites
Baz 421 Posted October 24, 2011 (edited) Just replied to your PM and said similar there. I have an E48 on my 8v. It's still up there really, it has loads of features that many basic current ECU's have these days. DTA is really one you'll want to ask your mapper about as he'll need to be set up for it. The software isn't the most straight forward and you can either use hot keys to navigate around or a Pot-box ideally. I'd have to seriously think about whether i want to use another DTA again when there's much simpler about. Edited October 24, 2011 by Baz Share this post Link to post Share on other sites
Miles 331 1 Cars Posted October 24, 2011 I'd make a loom up from scratch, modding existing looms is never good unless you replace the complete length of cable as joining them up is not a good idea at all. Share this post Link to post Share on other sites
craig_007 1 Posted October 25, 2011 Well decided on the Emerald M3D with K3 upgrade. Share this post Link to post Share on other sites
welshpug 1,737 Posted October 25, 2011 does the emerald drive the 4 wire MM icv? Share this post Link to post Share on other sites
Cameron 16 Posted October 25, 2011 The GTi6 one? Yep. Share this post Link to post Share on other sites
Anthony 1,003 Posted October 28, 2011 Are you sure Cameron? I thought that Emerald was only able to use 2-pin PWM type ICV's (e.g 1.9 Mi16) or 5 pin stepper motor (e.g K-Series) designs, and that the one that *wasn't* supported was the 4 pin ICV as used on most late 90's PSA cars? Share this post Link to post Share on other sites
Cameron 16 Posted October 28, 2011 Are you sure Cameron? I thought that Emerald was only able to use 2-pin PWM type ICV's (e.g 1.9 Mi16) or 5 pin stepper motor (e.g K-Series) designs, and that the one that *wasn't* supported was the 4 pin ICV as used on most late 90's PSA cars? Ah, I remember now.. what I did was yoink a 5-wire stepper motor off a Rover K-Series, which is a direct replacement for the GTi6 one on the plastic ICV housing. You just need to undo the 2 screws and swap them over. Share this post Link to post Share on other sites
welshpug 1,737 Posted October 28, 2011 nice, wonder if the S40 will work that one :hmm: Share this post Link to post Share on other sites