Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

Search the Community

Showing results for tags 'clearance'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Categories

  • Technical Articles & Guides
    • 205 GTI Basics & Buying Guides
    • Engine Maintenance & Upgrades
    • Gearbox & Drivetrain
    • Brakes, Suspension & Steering
    • Body, Interior and ICE
    • Misc & General Technical
  • Our Partners
  • Car Photo of the Month

Categories

  • Text

Forums

  • Links
    • 205 GTI Drivers Main Website
  • Support and News
    • Website & Forum Updates and News
  • Technical
    • XU 8v Engine Maintenance and Performance Upgrades
    • XU 16v Engine Maintenance and Performance Upgrades
    • XU Engine & Gearbox Service and Maintenance - ARCHIVE
    • XU Engine & Gearbox Modifications and Performance Upgrades - ARCHIVE
    • TU Engine Maintenance and Performance Upgrades
    • Non-XU/TU Engine Maintenance and Performance Upgrades
    • Aftermarket Engine Management Systems
    • Gearbox & Drivetrain
    • Brakes, Suspension & Steering
    • Body, Interior & ICE
    • Misc/General Technical
    • Other Model-specific Technical Questions
    • Technical Archive
    • 405Mi16.com Technical Forums Archive
  • General
    • General Car Chat
    • Drivers' Cars Discussion Topics
  • Car Projects & Works
    • Large Scale & Special Projects
    • Car Restorations, Overhauls & Upgrades
    • Trackday & Race/Rally Prep
    • Engine Work
    • Body, Misc & Non-Car Work
    • Projects & Works Starters
  • For Sale, Wanted and Group Buys
    • PugsForSale.co.uk Classifieds

Categories

  • Peugeot 205

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Found 1 result

  1. All right everybody? I had a few advisories on the 206cc last year so I’m getting them sorted this week. Up front I need to replace the springs and inner tie rods; all was going swimmingly until I came to the driver’s side lower ball joint. I only have the cup type separator which requires plenty of clearance above the ball joint to drive the pin through from the top but on the 206cc the drive shaft is still in place and there’s not enough movement on the driveshaft to push it through the hub with the steering knuckle in situ’ so I can't use the cup type separator. Likewise, there’s not enough clearance to remove the damper/strut without having first split the lower ball joint. So, the lower joint must come apart first but I just cannot get the damn thing fully separated. On the 205, I undid the pinch bolt and with a large spanner being used as a lever and a bit of hammering the lower arm came away from the steering knuckle, but on the 206cc, although it moves very freely to about half way out, it either gets stuck or I run out of droop on the lower arm and the lever I’m using just starts to bend. I’ve tried jacking the brake disc up to give me more downward travel on the lower arm but this seems to make the joint bind and I can’t get it to move at all. I’ve also hammered a wedge between the two ‘ears’ where the pinch bolt clamps to make sure these are spread but to no avail. I thought about buying a scissor type separator but it looks as though they just ‘crack’ the initial seal and are more suited to ball joints that have a nut on the top rather than a pinch bolt. Also, mine is already lose I just can’t get the lower arm far enough down to completely separate the joint. Here’s some pic’s showing how far it will move, first with a screwdriver and then with a large spanner. As you can see it’s really important that I get this done as I’ve discovered the driveshaft boot clip has snapped (and grease is everywhere!) so not only have I got to separate the lower arm in order to get the strut out I also need to pay some attention to the driveshaft and boot too! I guess my next option could be to try a fork type separator but I thought, before I spend out, I'd be best to ask here as I’m sure any suggestions will be helpful. Thanks all. Ian. ps. - I haven't looked at the passenger side yet as I'm doing a side at a time so I have a reference.
×