Jump to content
  • Welcome to 205GTIDrivers.com!

    Hello dear visitor! Feel free to browse but we invite you to register completely free of charge in order to enjoy the full functionality of the website.

matty_gti

[Engine_Work] The Graphites 2Nd Chapter: 2.1 Gti6 Turbo

Recommended Posts

matty_gti

After finally finishing off the Gti6 conversion project in my other thread and putting her away in the garage I thought that was it, job done! But as you do (we all know we do it!) I was looking around seeing what's out there and saw this engine come up for sale while on holiday in Greece...I knew I had to have it!

 

I'll get this project thread updated as and when I can! :)

 

3CC6A89D-457D-4585-AFD1-FCFDE06E8E11.jpg

 

6DD903FC-0E35-4F4C-A7C2-52A9A7D083CE.jpg

 

5368CF02-85CA-4CDD-8F4B-DD0E68CEE259.jpg

  • Like 1

Share this post


Link to post
Share on other sites
allanallen

Interesting inlet manifold! Car looks brilliant!

Share this post


Link to post
Share on other sites
johniban

interested in this! you got the engine from Greece?

Share this post


Link to post
Share on other sites
matty_gti

I picked the engine up from Sussex and found it while browsing eBay on holiday ;)

 

Got a couple more teaser picks before I put up the whole spec. Also started buying a some fuel parts I needed, bought a 1.5 litre swirl pot, Bosch 044 fuel pump, two sytec filters with high and low pressure filter elements, turbo smart FPR, fuel pressure gauge and a few sytec mounts...

 

22D0556D-EE47-4E5D-A271-A8FD00706795.jpg

 

2733D8A1-2EE5-466A-92EE-B1E59B55C3BE.jpg

 

F7F8E6EF-6905-4053-8043-FE2DE8ECE13F.jpg

 

16518D62-A23E-445B-8C1A-BE30A4E1680E.jpg

 

F47409BB-AFEA-4C6A-9A14-05B253E81441.jpg

  • Like 1

Share this post


Link to post
Share on other sites
j_turnell

Wow, looks awesome! Look forward to seeing build progress.

Share this post


Link to post
Share on other sites
allanallen

Bwrapppp pssssttttth! :)

 

Hope the spec includes cambelt covers!

Share this post


Link to post
Share on other sites
matty_gti

Can't wait for the noise!! Got a 3" bore exhaust system from the turbo back :)

 

The cam belt covers have been cut down to the bottom of the pulleys so should be ok, I think!

Share this post


Link to post
Share on other sites
tommy gun

I remember seeing this engine on eBay, even had a few bids but it got removed before the end I think.

Share this post


Link to post
Share on other sites
welshpug

Can't wait for the noise!! Got a 3" bore exhaust system from the turbo back :)

 

The cam belt covers have been cut down to the bottom of the pulleys so should be ok, I think!

 

eh?!

Share this post


Link to post
Share on other sites
wicked

Nice inlet manifold :wub: Where did one come from??

Share this post


Link to post
Share on other sites
matty_gti

Aldworth33 - Thanks, engine porn!

 

Tommy Gun - It got removed because I quickly bought it ;)

 

Welshpug - Can you elaborate?

 

Wicked - The manifold is made by Jenvey, will get some more pics of the setup over the weekend :)

Share this post


Link to post
Share on other sites
tommy gun

You must have plenty of cash, he wanted big bucks for that engine.

Look forward to seeing more progress.

Share this post


Link to post
Share on other sites
GilesW

Is this what's-his-names from Haywards Heath?

If so its know yo have been an awesome car.

 

Buy any of the running gear etc he had for sale too? (Mostly satchel stuff iirc).

Share this post


Link to post
Share on other sites
matty_gti

Yeah that's the one Giles, he had already broken down and sold most of the other suspension parts etc and only had odd bits left.

 

We spoke about the engine for a while and I weighed up how much this sort of spec would cost me if I were to build it so eventually we came to a price we were both happy with.

 

The spec:

 

Engine,

2.1l bored and stroked

Wossner 86.5mm forged pistons

PEC Con Rods

ACL bearings through out

ARP rod and crank bolts

ARP head stud and nut kit

Commetic MLS head gasket

AMS ported head

1mm oversized stainless inlet and exhaust race valves with 3 angle seats

CAT cams turbo profile inlet and exhaust cams

CAT cams double valve springs, solid lifters, caps and retainers

CAT cams adjustable pulleys

Custom made tubular exhaust manifold and downpipe

GT30AR50 Garrett roller bearing turbo

Tail 44mm external wastegate

Light weight race alternator with custom pulley

Jenvey duel plenum intake manifold and throttle body

680cc Bosch fuel injectors

 

Engine management,

KMS MD35 ECU

KMS wide band lambda sensor and controller

Custom wiring loom

Gizzmo IBC

 

Gearbox,

Late BE3 casing

Quaife close ratio gear set

Custom made final drive for correct gearing of the turbo engine

Gripper LSD

Billet steel light weight flywheel

Helix paddle clutch

Custom made driveshafts

Complete short shift rose jointed gear linkage and lever

 

All in all, 405bhp at 1.5bar

Share this post


Link to post
Share on other sites
camgti

WP is concered about the oulley covers as they can prove vital.

 

I learnt the hard way as a kid. Had them off to look cool. Somehow a stone/nut/bolt something was flung into the timing area and pop went the weasel. Get some covers on the for insurance.

 

Very nice spec engine. Should be an absolute weapon! Will sound awesome, espexially with those larger valves!

Share this post


Link to post
Share on other sites
j_turnell

Impressive spec, although i'd be a bit dubious of the KMS! Making use of all those horses is going to be bit of an issue...

Share this post


Link to post
Share on other sites
matty_gti

I think it's time for an update! Made some progress so will get some pictures up as we all know they do the talking...

Share this post


Link to post
Share on other sites
matty_gti

Started on the fuel system first and then swapped over the engine.

 

746D2DF7-B594-4AD3-B11F-CA74C4A01042.jpg

 

6A1EB936-8385-4DEE-816E-94419ACF4101.jpg

 

C804E7EF-67C8-41EB-93F5-0C6FB1184A22.jpg

 

095E92A5-7DA7-48F4-9539-845FE4924BD2.jpg

 

C3742861-1BC7-426E-B725-B7F010D76890.jpg

 

DAC0791A-21A4-49EA-A4A0-AAD85845A71B.jpg

Share this post


Link to post
Share on other sites
allye

Holy bloody s*ite balls. Impressive stuff. I know it vulgar but please tell, how much dollar is tied up in that fuel system?

Share this post


Link to post
Share on other sites
matty_gti

i think its around £1300 but I don't want to look at any receipts until the things finished! :)

Share this post


Link to post
Share on other sites
cybernck

WOW! Impressive thread! Why are there no updates though? :unsure:

Share this post


Link to post
Share on other sites
matty_gti

It's been a long time, everything seems to get in the way! I've made some progress, engine is in and the exhaust has been made. It's taking a while getting the rad and oil cooler in place with the fans as want it looking fairly standard and original. I'll have a look for some pics.

Share this post


Link to post
Share on other sites
johniban

Will be a great car when done! 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×